計量泵與管道離心泵的安裝方式有什么區別
很多客戶在購買了VAREM計量泵與管道離心泵后，不知道怎么安裝。相信大家都知道，管道離心泵是最常見的一種泵浦，一般的水電工都熟悉。但是計量泵是最近十幾年才在國內大范圍生產與應用的。那么計量泵與管道離心泵的安裝方式有什么區別呢？我們先來了解下兩者的概念。先來說說管道離心泵，它是為管道增壓輸送，解決管道壓力過低而研制的新穎泵，比目前應用臥式離心泵具有很大的優越性。管道泵的優點主要體現在以下幾點:
1.管道泵適用于高層建筑加壓供水、園林噴灌、冷卻塔供水、長距離供水、空調、制冷沖洗、浴室降溫等。溫水循環加壓，使用溫度在80℃以下。
2.適用于供暖、鍋爐等行業的高溫熱水加壓循環。使用溫度低于150℃。
3.適用于食品、制藥、釀酒、化工等行業工藝過程中輸送腐蝕性介質，使用溫度在80℃以下。
4.適用于輸送非腐蝕性液體、甲烷或煤礦井下固定設備為一類、工廠為IIA類、IIB類、溫度組為T1、T2、T3、T4、存在爆炸性混合物的其他工業場所。使用溫度低于80℃。
5.管道泵適用于輸送化工、制藥、石油、食品、國防等行業的腐蝕性液體，以及甲烷或煤礦井下固定設備一級、工廠IIA級、IIB級、溫度組T1、T2、T3、T4、爆炸性混合物等工業場所。使用溫度低于150℃。
上海龍亞公司專業從事VAREM計量泵和管道離心泵的生產和銷售，公司負責:質量是贏得信任的砝碼，是成功的關鍵！繼續做泵客戶合格的支持供應商！公司使命:堅持為客戶提供可靠、穩定、耐用、故障率低、性價比高的泵類產品！核心價值觀:誠實務實、勇于承擔責任、合作共贏；專注專業，激情進取，不斷創新。這個世界上，不缺著急的人。缺少的是低頭拉車繼續走自己的路的人！
1.管道離心泵1安裝前的準備。準備安裝工具和起重設備；2.在運輸過程中，檢查ZILMET泵裝置的部件是否松動和損壞；3.檢查基礎是否平整。管道離心泵安裝注意事項:1。柔性接頭2。手肘3。閘閥4。直管(取壓管)5。泵6。7號基地。支撐結構8。減震器2。管道離心泵1的安裝順序。機組運到現場時，水泵和電機已經由底座的附屬人員校準，安裝非常方便。2.將底座放在基礎上，將楔形鐵墊在地腳螺栓附近，找平后將底座抬高20~40 mm，以填充水泥漿；3.用水平儀檢查基層的水平度，找平后用水泥漿填充基層，待水泥干透后再檢查水平度；4.當機組功率較大時，泵、電機和底座可單獨包裝，以方便運輸。此時，用戶需要自行安裝和校正水泵機組。方法如下:a .清理底座支撐面、水泵腳和電機腳平面上的污垢，將水泵和電機放在底座上；b、調整泵軸的水平，調平后，用螺栓將泵固定在底座上，防止行走；c、抬起電機，使泵聯軸器和電機聯軸器配合，將電機降到底座上的相應位置；d、將兩聯軸器間隙調整到5mm左右，校正電機軸和泵軸的軸線是否重合。方法是將直尺放在聯軸器上，兩個聯軸器的外圓應與直尺平齊。如果不重合，調整電機或泵的相對位置，或用薄鐵皮調整；e、為了檢查安裝精度，用測隙規測量聯軸器圓周上幾個不同位置的兩個聯軸器平面之間的間隙。一周內聯軸器平面上的最大間隙和最小間隙之差不得超過0.3毫米，兩端上下或左右中心線之差不得超過0.1毫米..5.當機組沒有底座時，需要直接安裝在基礎上。方法類似于4，但更要注意校準。三、管道離心泵安裝注意事項1。安裝時，管道不應壓在泵上，否則容易損壞泵；2.安裝時，必須擰緊地腳螺栓，并定期檢查機組，防止松動，以免泵啟動和運行時產生影響泵性能的巨大振動；3.安裝水泵前，應仔細檢查有無影響水泵運行的硬物(如石頭、鐵砂)，以免水泵運行時損壞過流部件；4.為了便于維護和安全使用，泵的進出口管道上應安裝調節閥，泵的進出口法蘭上應安裝壓力表。對于高揚程泵，為防止水錘，應在出口閘閥前安裝止回閥，以應對突然停電等停電事故，從而保證泵在最佳工況下運行，延長泵的使用壽命；5.泵用于吸入場合時，應配有底閥，進氣管道不應有過多的彎頭，同時不應有漏水或漏氣現象，以免影響泵的吸入性能；6.為了防止雜質進入泵內而堵塞流道會影響性能，應在VAREM泵入口前安裝過濾器；7.管道安裝前，轉動水泵的轉子部件，不應有摩擦聲或卡澀現象，否則應拆開水泵檢查原因；上海龍亞泵閥品牌服務承諾:在質量保證期內對缺陷產品進行修理、更換和退貨；所有質量投訴應在24小時內得到答復。應派遣服務人員離開現場，不排除故障或做出結論。本廠生產的配件均為原裝配件。我廠生產的產品及配件具有通用性，與原廠型號兼容。如有安裝尺寸和質量問題，我們將無條件退換，所有設備終身服務！(整機保修一年，易損件除外)。全國各地區售后部門聯系方式:上海400-001-5655(其他地區聯系方式請來電)！
下面來說說計量泵，計量泵一般都是工行業中用于輸送那些具有腐蝕性的液體的一種特俗容積泵。在高速發展的時代下，如今有許多的行業興起，比如制藥、食品飲料和石油化工還有化學工業等在內的各個領域，在工藝制作的過程中往往會有較強的腐蝕性酸性的液體產生，這時候就需要用到機械隔膜計量泵，這也是機械隔膜計量泵在工行業中的主要運用。計量泵如今大都是運用在工行業中，因為其穩定性和可控性而受到業內一致好評，也因此在市場上有著較好的前景。計量泵的安裝其實與管道離心泵是類似的，計量泵的液力端包括：泵頭，隔膜，閥，背板和安裝螺栓。只要安裝固定螺栓和進出口管道即可。
What is the difference between metering pump and pipeline centrifugal pump
Many customers do not know how to install the varem metering pump and pipeline centrifugal pump. I believe we all know that the pipeline centrifugal pump is the most common pump, which is familiar to the General Hydropower workers. However, the metering pump has been produced and applied on a large scale in China for more than ten years. What is the difference between metering pump and pipeline centrifugal pump? Let's first understand the concepts of the two. Let's talk about the pipeline centrifugal pump first. It is a new pump developed for pipeline pressurization and transportation to solve the problem of low pipeline pressure. It has great advantages over the current application of horizontal centrifugal pump. The advantages of pipeline pump are mainly reflected in the following points:
1. Pipe pump is suitable for high-rise building pressurized water supply, garden sprinkler irrigation, cooling tower water supply, long-distance water supply, air conditioning, refrigeration washing, bathroom cooling, etc. The temperature is below 80 ℃.
2. It is suitable for high temperature hot water pressurized circulation in heating, boiler and other industries. The operating temperature is lower than 150 ℃.
3. It is suitable for conveying corrosive medium in the process of food, pharmaceutical, wine making, chemical industry and other industries, and the service temperature is below 80 ℃.
4. It is suitable for conveying non corrosive liquid, methane or other industrial places with class I fixed equipment in coal mine, class IIa and IIB factory, T1, T2, T3 and T4 temperature group and explosive mixture. The use temperature is lower than 80 ℃.
5. Pipeline pump is suitable for conveying corrosive liquid in chemical, pharmaceutical, petroleum, food, national defense and other industries, as well as industrial places such as methane or underground fixed equipment class I, factory class IIa, class IIB, temperature group T1, T2, T3, T4, explosive mixture, etc. The use temperature is lower than 150 ℃.
Shanghai Longya company specializes in the production and sales of varem metering pump and pipeline centrifugal pump. The company is responsible for: quality is the weight to win trust and the key to success! Continue to be a qualified support supplier for pump customers! Company mission: to provide reliable, stable, durable, low failure rate, cost-effective pump products for customers! Core values: honesty and pragmatism, the courage to take responsibility, win-win cooperation; focus on professional, passion and innovation. There is no shortage of anxious people in this world. What is lacking is the person who lowers his head and continues to walk his own way!
1. Preparation before installation of pipeline centrifugal pump 1. Prepare installation tools and lifting equipment; 2. Check whether the parts of zilmet pump unit are loose and damaged during transportation; 3. Check whether the foundation is flat. Precautions for installation of pipeline centrifugal pump: 1. Flexible joint 2. Elbow 3. Gate valve 4. Straight pipe (pressure pipe) 5. Pump 6. Base seven. Support structure 8. Shock absorber 2. Installation sequence of pipeline centrifugal pump 1. When the unit is transported to the site, the water pump and motor have been calibrated by the auxiliary personnel of the base, so the installation is very convenient. 2. Place the base on the foundation, place the wedge iron pad near the anchor bolt, raise the base 20 ~ 40 mm after leveling to fill the cement slurry; 3. Check the levelness of the base with the level meter, fill the base with the cement slurry after leveling, and check the levelness after the cement is dry; 4. When the power of the unit is high, the pump, motor and base can be packed separately to facilitate transportation. At this time, the user needs to install and calibrate the pump unit. The methods are as follows: a . clean the dirt on the supporting surface of the base, the water pump foot and the motor foot plane, and put the water pump and the motor on the base; B. adjust the level of the pump shaft, and after leveling, fix the pump on the base with bolts to prevent walking; C. lift the motor to make the pump coupling and the motor coupling cooperate, and lower the motor to the corresponding position on the base; D. adjust the gap between the two couplings to about 5mm, and correct Whether the axes of motor shaft and pump shaft coincide. The method is to place the ruler on the coupling, and the outer circles of the two couplings should be flush with the ruler. If it does not coincide, adjust the relative position of motor or pump, or adjust it with thin sheet iron; e. in order to check the installation accuracy, measure the clearance between two coupling planes at several different positions on the coupling circumference with a feeler gauge. Within one week, the difference between the maximum clearance and the minimum clearance on the plane of the coupling shall not exceed 0.3mm, and the difference between the upper and lower or left and right center lines at both ends shall not exceed 0.1mm.. 5. When the unit has no base, it needs to be directly installed on the foundation. The method is similar to 4, but more attention should be paid to calibration. 3、 Precautions for installation of pipeline centrifugal pump 1. During the installation, the pipeline should not be pressed on the pump, otherwise it is easy to damage the pump; 2. During the installation, the foundation bolts must be tightened, and the unit must be checked regularly to prevent loosening, so as to avoid the huge vibration that affects the pump performance during the start-up and operation of the pump; 3. Before the installation of the pump, it is necessary to carefully check whether there are any hard objects (such as stone and iron sand) that affect the operation of the pump, so as to avoid damaging the flow passage parts during the operation of the pump; 4 In order to facilitate maintenance and safe use, regulating valves should be installed on the inlet and outlet pipes of the pump, and pressure gauges should be installed on the inlet and outlet flanges of the pump. For high lift pump, in order to prevent water hammer, a check valve should be installed in front of the outlet gate valve to deal with sudden power failure and other power failure accidents, so as to ensure the operation of the pump under the best working conditions and prolong the service life of the pump; 5. When the pump is used in suction occasions, it should be equipped with bottom valve, the inlet pipe should not have too many elbows, and there should be no water leakage or air leakage, so as not to affect the suction performance of the pump; 6 In order to prevent impurities from entering the pump and blocking the flow channel will affect the performance, the filter should be installed before the entrance of the varem pump; 7. Before the pipeline installation, the rotor parts of the pump should be rotated without friction sound or jam, otherwise the pump should be disassembled to check the cause; Shanghai Longya pump valve brand service commitment: repair, replace and return the defective products within the warranty period; all quality complaints A response should be received within 24 hours. Service personnel shall be dispatched to leave the site without troubleshooting or making conclusions. The accessories produced by our factory are original ones. Our products and accessories are universal and compatible with the original model. If there are installation size and quality problems, we will return unconditionally, all equipment life-long service! (the whole machine is guaranteed for one year, except for wearing parts). Contact information of after-sales departments in all regions of China: Shanghai 400-001-5655 (please call for contact information in other regions)!
Let's talk about the metering pump, which is generally used to transport those corrosive liquids in the industry. In the era of rapid development, now there are many industries rising, such as pharmaceutical, food and beverage, petrochemical and chemical industry, etc. in the process of production, there are often strong corrosive acid liquid. At this time, we need to use mechanical diaphragm metering pump, which is also the main application of mechanical diaphragm metering pump in the industry. Nowadays, metering pump is mostly used in the industry, because of its stability and controllability, it is highly praised in the industry, so it has a good prospect in the market. The installation of metering pump is similar to that of pipeline centrifugal pump. The hydraulic end of metering pump includes pump head, diaphragm, valve, back plate and mounting bolt. Just install the fixing bolts and the inlet and outlet pipes.